View Shopping Cart" title="View Shopping Cart
Toll Free 1 (877) 470-2975

Chevelle, El Camino, Malibu, Monte Carlo 1978-1988 Drag Race Upper Control Arms #TLC-88


Control arms, Bushings, Shafts
Chevelle, El Camino, Malibu, Monte Carlo 1978-1988 Drag Race Upper Control Arms #TLC-88
Lightweight tubular upper control arms for Chevelle, El Camino, Malibu, Monte Carlo (model years--1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, and 1988) are now available from Global West. They are shipped fully assembled. Part # TLC-88 includes:
  • Tubular powder coated black upper tubular arms
  • Upper ball joints
  • Control arm bump stops
  • Aluminum billet upper cross shafts
  • Delrin bushings and related hardware
  • The control arms are fully assembled with billet aluminum cross shafts, special Delrin bushings, and shortened bump stops.
  • They are made out of 4130 chrome-molly and shave almost a full 10 pounds off the front end over stock control arms.
The Global West Advantage: In addition bump steer is reduced through new geometry induced by the control arm. Bump steer is a condition that occurs as the front of the vehicle raises, the wheels turn on there own without driver input. This causes tire scrub and front end wander. Note: Currently the stock upper control arms change the toe approximately 3/8 of an inch per 1 inch of travel. TLC-88 drops the toe change down to 1/8 inch for the same amount of travel. Plus TLC upper arms have 6 degrees of caster built into the arm. The stock arm usually tops out at 3 degrees with full shim packs. Geometry Change: One of the biggest problems most production cars have is not enough caster. Caster provides straight-line stability and reduces wander at high speed. It is part of the front end self-aligning force. For this reason, caster is essential on drag cars. Unfortunately, there is never enough caster available using stock front-end components. Too many alignment shims are needed and possible camber problems can occur. TLC upper control arms are built with additional positive caster and setting camber is never a problem. Control Arm Shafts: All TLC upper control arms use billet aluminum cross-shafts. Steel sleeves are pressed in on each side of the shaft for protection. The sleeves isolate the aluminum shaft from alignment shims, frame bolts and nuts. This allows proper torque to be maintained on the cross-shaft. Without steel sleeves, alignment shims and upper shaft bolts would rest against the aluminum shaft and eventually work loose. Once the bolt works loose, alignment shims would fall out causing loose alignment. TLC Upper and Lower Control Arm Bushings: TLCs use Delrin type bushings machined specifically for our shafts and housings. Delrin, which is patented, is a hard plastic and can handle extreme loads associated with suspension components. It is long lasting and very durable. Grease fittings are installed in the control arms for lubricating the bushings. Synthetic grease is recommended. Bump Stops: Bump stops are installed on the upper control arms to stop ball joint over travel. This protects the upper ball joint from damage. Sometimes, if the front end travel needs to be limited, the bump stop may be removed and a limiter may be added in its place. Always check the suspension travel. Make sure the bump stop contacts the frame before the shock runs out of travel. Modifications to the suspension can change the distance required.

https://www.globalwest.netchevelle-el-camino-malibu-monte-carlo-drag-race-upper-control-arms-1978-1979-1980-1981-1982-1983-198.html
$581.00
Drag race upper arms for 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, and 1988 GM G-body cars. -Made in the USA!
Drag race upper arms for 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, and 1988 GM G-body cars. -Made in the USA!(Left to right) Ball joint, bump-stop, billet aluminum shaft
Click to Enlarge


Lightweight tubular upper control arms for Chevelle, El Camino, Malibu, Monte Carlo (model years--1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, and 1988) are now available from Global West. They are shipped fully assembled.

Part # TLC-88 includes:
  • Tubular powder coated black upper tubular arms
  • Upper ball joints
  • Control arm bump stops
  • Aluminum billet upper cross shafts
  • Delrin bushings and related hardware
  • The control arms are fully assembled with billet aluminum cross shafts, special Delrin bushings, and shortened bump stops.
  • They are made out of 4130 chrome-molly and shave almost a full 10 pounds off the front end over stock control arms.
The Global West Advantage:

In addition bump steer is reduced through new geometry induced by the control arm. Bump steer is a condition that occurs as the front of the vehicle raises, the wheels turn on there own without driver input. This causes tire scrub and front end wander.

Note: Currently the stock upper control arms change the toe approximately 3/8 of an inch per 1 inch of travel. TLC-88 drops the toe change down to 1/8 inch for the same amount of travel. Plus TLC upper arms have 6 degrees of caster built into the arm. The stock arm usually tops out at 3 degrees with full shim packs.

Geometry Change: One of the biggest problems most production cars have is not enough caster. Caster provides straight-line stability and reduces wander at high speed. It is part of the front end self-aligning force. For this reason, caster is essential on drag cars. Unfortunately, there is never enough caster available using stock front-end components. Too many alignment shims are needed and possible camber problems can occur. TLC upper control arms are built with additional positive caster and setting camber is never a problem.

Control Arm Shafts: All TLC upper control arms use billet aluminum cross-shafts. Steel sleeves are pressed in on each side of the shaft for protection. The sleeves isolate the aluminum shaft from alignment shims, frame bolts and nuts. This allows proper torque to be maintained on the cross-shaft. Without steel sleeves, alignment shims and upper shaft bolts would rest against the aluminum shaft and eventually work loose. Once the bolt works loose, alignment shims would fall out causing loose alignment.

TLC Upper and Lower Control Arm Bushings: TLCs use Delrin type bushings machined specifically for our shafts and housings. Delrin, which is patented, is a hard plastic and can handle extreme loads associated with suspension components. It is long lasting and very durable. Grease fittings are installed in the control arms for lubricating the bushings. Synthetic grease is recommended.

Bump Stops: Bump stops are installed on the upper control arms to stop ball joint over travel. This protects the upper ball joint from damage. Sometimes, if the front end travel needs to be limited, the bump stop may be removed and a limiter may be added in its place. Always check the suspension travel. Make sure the bump stop contacts the frame before the shock runs out of travel. Modifications to the suspension can change the distance required.
$581.00
Qty:
Instructions
Chevelle, El Camino, Malibu, Monte Carlo 1978-1988 Drag Race Upper Control Arms #TLC-88
Item #:TLC-88_
Availability:
View Shipping Policy
Only:$581.00
Quantity:
Instructions


Product Description


Lightweight tubular upper control arms for Chevelle, El Camino, Malibu, Monte Carlo (model years--1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, and 1988) are now available from Global West. They are shipped fully assembled.

Part # TLC-88 includes:
  • Tubular powder coated black upper tubular arms
  • Upper ball joints
  • Control arm bump stops
  • Aluminum billet upper cross shafts
  • Delrin bushings and related hardware
  • The control arms are fully assembled with billet aluminum cross shafts, special Delrin bushings, and shortened bump stops.
  • They are made out of 4130 chrome-molly and shave almost a full 10 pounds off the front end over stock control arms.
The Global West Advantage:

In addition bump steer is reduced through new geometry induced by the control arm. Bump steer is a condition that occurs as the front of the vehicle raises, the wheels turn on there own without driver input. This causes tire scrub and front end wander.

Note: Currently the stock upper control arms change the toe approximately 3/8 of an inch per 1 inch of travel. TLC-88 drops the toe change down to 1/8 inch for the same amount of travel. Plus TLC upper arms have 6 degrees of caster built into the arm. The stock arm usually tops out at 3 degrees with full shim packs.

Geometry Change: One of the biggest problems most production cars have is not enough caster. Caster provides straight-line stability and reduces wander at high speed. It is part of the front end self-aligning force. For this reason, caster is essential on drag cars. Unfortunately, there is never enough caster available using stock front-end components. Too many alignment shims are needed and possible camber problems can occur. TLC upper control arms are built with additional positive caster and setting camber is never a problem.

Control Arm Shafts: All TLC upper control arms use billet aluminum cross-shafts. Steel sleeves are pressed in on each side of the shaft for protection. The sleeves isolate the aluminum shaft from alignment shims, frame bolts and nuts. This allows proper torque to be maintained on the cross-shaft. Without steel sleeves, alignment shims and upper shaft bolts would rest against the aluminum shaft and eventually work loose. Once the bolt works loose, alignment shims would fall out causing loose alignment.

TLC Upper and Lower Control Arm Bushings: TLCs use Delrin type bushings machined specifically for our shafts and housings. Delrin, which is patented, is a hard plastic and can handle extreme loads associated with suspension components. It is long lasting and very durable. Grease fittings are installed in the control arms for lubricating the bushings. Synthetic grease is recommended.

Bump Stops: Bump stops are installed on the upper control arms to stop ball joint over travel. This protects the upper ball joint from damage. Sometimes, if the front end travel needs to be limited, the bump stop may be removed and a limiter may be added in its place. Always check the suspension travel. Make sure the bump stop contacts the frame before the shock runs out of travel. Modifications to the suspension can change the distance required.
Email Year Make Model We respect your privacy.
We accept Visa, Mastercard, American Express, Discover 256bit encryption


Copyright © 2022 Global West Suspension Components Inc.