View Shopping Cart" title="View Shopping Cart
Toll Free 1 (877) 470-2975

Rear Stock Insulator Replacement 1979-04 Mustang- part # 1301


Ford Coil Spring Spacers
Rear Stock Insulator Replacement 1979-04 Mustang- part # 1301
Rear Coil Spring Spacer- Polyurethane Stock Insulator Replacement Coil Spring Spacers are used to raise the vehicle up if its too low, leveling it, and for weight jacking if the car is being raced. For most applications, coil sprig spacers are installed under the coil spring between the coil and the lower control arm. Some are installed on top of the coil spring between it and the frame. We offer three styles of spacers: Aluminum, Polyurethane, and Rubber. The applications determine which is available. Selecting a coil spring spacer for the front end has a simple formula you must remember, one-inch at the spring equals two-inches at the body. This applies to all Ford and GM models we deal with. Example 1: Lets say you want to raise your 1969 Camaro one-inch in the front. You would purchase two 1/2 inch spacers; one for each side. They install between the lower arm and spring. Your ride height will go up one full inch. Example 2: Lets say you want to raise the front of your GTO 1-1/2 inches because you cut to much off the spring. Using the formula, one at the spring is two at the body, a 3/4 inch spacer is required to lift the front end up 1-1/2 inches. Ford works the same way. Rear spring spacers are available in polyurethane or aluminum. All of the rear spacers that raise the vehicle are made out of aluminum. Polyurethane is used for replacing the factory spring cushion. The formula for the rear GM models is one to one. Therefore if you want to raise the car 3/4 of an inch, use a 3/4 inch spacer. Ford Models 1979-04 Mustangs rear follow a different formula. To keep matters simple we have listed the lift for the three spacers we provide. NOTE: Non-independent rear. Part# 1200- will lift the rear 5/8 of an inch Part# 1201- will lift the rear 7/8 of an inch Part# 1202- will lift the rear 1-1/4 inches
https://www.globalwest.net1301-ford.html
$23.23
Rear Stock Insulator Replacement 1979-04 Mustang- part # 1301
Click to Enlarge
Rear Coil Spring Spacer- Polyurethane Stock Insulator Replacement

Coil Spring Spacers are used to raise the vehicle up if its too low, leveling it, and for weight jacking if the car is being raced. For most applications, coil sprig spacers are installed under the coil spring between the coil and the lower control arm. Some are installed on top of the coil spring between it and the frame. We offer three styles of spacers: Aluminum, Polyurethane, and Rubber. The applications determine which is available.

Selecting a coil spring spacer for the front end has a simple formula you must remember, one-inch at the spring equals two-inches at the body. This applies to all Ford and GM models we deal with. Example 1: Lets say you want to raise your 1969 Camaro one-inch in the front. You would purchase two 1/2 inch spacers; one for each side. They install between the lower arm and spring. Your ride height will go up one full inch. Example 2: Lets say you want to raise the front of your GTO 1-1/2 inches because you cut to much off the spring. Using the formula, one at the spring is two at the body, a 3/4 inch spacer is required to lift the front end up 1-1/2 inches. Ford works the same way.

Rear spring spacers are available in polyurethane or aluminum. All of the rear spacers that raise the vehicle are made out of aluminum. Polyurethane is used for replacing the factory spring cushion. The formula for the rear GM models is one to one. Therefore if you want to raise the car 3/4 of an inch, use a 3/4 inch spacer.

Ford Models 1979-04 Mustangs rear follow a different formula. To keep matters simple we have listed the lift for the three spacers we provide. NOTE: Non-independent rear.

Part# 1200- will lift the rear 5/8 of an inch

Part# 1201- will lift the rear 7/8 of an inch

Part# 1202- will lift the rear 1-1/4 inches
$23.23
Qty:
Rear Stock Insulator Replacement 1979-04 Mustang- part # 1301
Item #:1301
Availability:
View Shipping Policy
Only:$23.23
Quantity:


Product Description
Rear Coil Spring Spacer- Polyurethane Stock Insulator Replacement

Coil Spring Spacers are used to raise the vehicle up if its too low, leveling it, and for weight jacking if the car is being raced. For most applications, coil sprig spacers are installed under the coil spring between the coil and the lower control arm. Some are installed on top of the coil spring between it and the frame. We offer three styles of spacers: Aluminum, Polyurethane, and Rubber. The applications determine which is available.

Selecting a coil spring spacer for the front end has a simple formula you must remember, one-inch at the spring equals two-inches at the body. This applies to all Ford and GM models we deal with. Example 1: Lets say you want to raise your 1969 Camaro one-inch in the front. You would purchase two 1/2 inch spacers; one for each side. They install between the lower arm and spring. Your ride height will go up one full inch. Example 2: Lets say you want to raise the front of your GTO 1-1/2 inches because you cut to much off the spring. Using the formula, one at the spring is two at the body, a 3/4 inch spacer is required to lift the front end up 1-1/2 inches. Ford works the same way.

Rear spring spacers are available in polyurethane or aluminum. All of the rear spacers that raise the vehicle are made out of aluminum. Polyurethane is used for replacing the factory spring cushion. The formula for the rear GM models is one to one. Therefore if you want to raise the car 3/4 of an inch, use a 3/4 inch spacer.

Ford Models 1979-04 Mustangs rear follow a different formula. To keep matters simple we have listed the lift for the three spacers we provide. NOTE: Non-independent rear.

Part# 1200- will lift the rear 5/8 of an inch

Part# 1201- will lift the rear 7/8 of an inch

Part# 1202- will lift the rear 1-1/4 inches
Email Year Make Model We respect your privacy.
We accept Visa, Mastercard, American Express, Discover 256bit encryption


Copyright © 2022 Global West Suspension Components Inc.